Back adhesive honeycomb warning-strip white lattice reflective strip 3mx5cm reflective body sticker
$0.39
- 1688 Link: View 1688 Product
- Product Code: EPCS15881
- Availability: In Stock
- 2 or more $0.39
- 1000 or more $0.38
- 2000 or more $0.37
Product Name: Back adhesive honeycomb warning-strip, white lattice reflective warning-strip, 3mx5cm reflective body sticker
Size: 3mx5cm
Colors: White/Red/Golden/Fluorescent Yellow/Green/Blue
Attention: Reflective car stickers are not night lights and require light refraction to reflect. The dimensions are manually measured and the error is normal
instructions:
1: Firstly, all car stickers in the store are composed of three parts: the first layer is a transparent transfer film with moderate adhesion (which needs to be removed after pasting the car sticker), the second layer is the car sticker, and the third layer is the base paper, usually yellow (the materials we use are mainly Weishi Bai A-level reflective film and Taiwan KK car sticker special film).
2:Due to the fact that the stickers are rolled up during packaging and shipping, bubbles may sometimes appear on the yellow base paper and transfer film. This is a normal phenomenon and will not affect the adhesive effect of the car stickers. Before pasting, place it on a flat tabletop and use a scraper or credit card to flatten it.
3:Please note: The correct way to remove the car sticker is to first remove the backing paper, rather than directly tearing off the transfer film. When removing the backing paper, it is necessary to operate slowly, and the speed should be such that the car sticker does not stick to the yellow backing paper.
4:First, determine the location to be pasted, and after cleaning, you can open the sticker:
1. Dry pasting method (applicable for car stickers within 30CM): Compare the angle of the car sticker at the position to be pasted, and after confirming, press and hold the two corners of the left transfer film, scraping while pasting to ensure that there are no bubbles inside the car sticker. After the entire sticker is posted, use a scraper or credit card to scrape the flat sticker. Be careful not to apply too much force here, otherwise it will damage the transfer film and affect the effectiveness of the sticker.
2. Wet pasting method (suitable for large vehicles over 30CM): Use clean water to evenly spray water on the position to be pasted and the car sticker with the bottom paper removed. First, gently apply the sticker, adjust the angle and position, and slowly scrape the water from one side to the other.
5:After pasting, be careful to remove the transfer film. In winter, you can blow it with a hot air sprayer (or use a hair dryer) to ensure that the car sticker is completely firmly attached to the car. After completion, try not to wash the car as much as possible, usually for about three days.
Size: 3mx5cm
Colors: White/Red/Golden/Fluorescent Yellow/Green/Blue
Attention: Reflective car stickers are not night lights and require light refraction to reflect. The dimensions are manually measured and the error is normal
instructions:
1: Firstly, all car stickers in the store are composed of three parts: the first layer is a transparent transfer film with moderate adhesion (which needs to be removed after pasting the car sticker), the second layer is the car sticker, and the third layer is the base paper, usually yellow (the materials we use are mainly Weishi Bai A-level reflective film and Taiwan KK car sticker special film).
2:Due to the fact that the stickers are rolled up during packaging and shipping, bubbles may sometimes appear on the yellow base paper and transfer film. This is a normal phenomenon and will not affect the adhesive effect of the car stickers. Before pasting, place it on a flat tabletop and use a scraper or credit card to flatten it.
3:Please note: The correct way to remove the car sticker is to first remove the backing paper, rather than directly tearing off the transfer film. When removing the backing paper, it is necessary to operate slowly, and the speed should be such that the car sticker does not stick to the yellow backing paper.
4:First, determine the location to be pasted, and after cleaning, you can open the sticker:
1. Dry pasting method (applicable for car stickers within 30CM): Compare the angle of the car sticker at the position to be pasted, and after confirming, press and hold the two corners of the left transfer film, scraping while pasting to ensure that there are no bubbles inside the car sticker. After the entire sticker is posted, use a scraper or credit card to scrape the flat sticker. Be careful not to apply too much force here, otherwise it will damage the transfer film and affect the effectiveness of the sticker.
2. Wet pasting method (suitable for large vehicles over 30CM): Use clean water to evenly spray water on the position to be pasted and the car sticker with the bottom paper removed. First, gently apply the sticker, adjust the angle and position, and slowly scrape the water from one side to the other.
5:After pasting, be careful to remove the transfer film. In winter, you can blow it with a hot air sprayer (or use a hair dryer) to ensure that the car sticker is completely firmly attached to the car. After completion, try not to wash the car as much as possible, usually for about three days.
| Product Info | |
| Brand | None |
| Installation method | Adhesive type |
| Is it a patented supply? | No |
| Is it a special supply source for cross-border export? | Yes |
| Main downstream platform | Lazada |
| Main sales areas | Other |
| Material | Stickers |
| Pattern | Honeycomb |
| Processing and customization | Yes |
| Product Code | L-51 |
| There are authorizable private brands | No |
| Type | car sticker |
Tags: Back, adhesive, honeycomb, warningstrip, white, lattice, reflective, strip, mxcm, body, sticker